MY 250İ USER MANUAL (V1.09) Elektralite is a division of Group One. 70, Sea Lane, Farmingdale, NY 11735, USA. Tel: +1 (516)-249-3662. Fax: +1 (51
9The display panel. The display panel on MY 250Ì offers many features. For example, you can set the starting address, switch on and off the lamp, run
10Main functions - Main menu 0 1. Press [ENTER] for 3 seconds to enter the main menu "MODE" (display flashing) 2. Press [ENTER] and sele
11 1. Select "AUTO" or "SOUN" by pressing [UP]. 2. Press [ENTER] for selecting the desired extension menu. 3. Select "ALON&
12 1. Press [ENTER] for 3 seconds to enter the main menu (display flashing). 2. Press [UP] to select “LAMP”. - Lamp on/off This function switches t
134. Press [ENTER] or [EXIT/DN] to exit. - Tilt Reverse This function reverses the Tilt movement. 1. Select “rTIL” by pressing [UP] button. 2. Press
14With this function you can adjust the lamp via the Control Board. The shutter opens and the lamp can be adjusted. In this mode, the device will not
15lamp. 1. Select “CLLT” by pressing [UP] button. 2. Press [ENTER], the display shows “ON” or “OFF”. 3. Press [UP] to select “ON” to enable this func
16b) Editing via the external controller Call up the first scene in your controller now. 1. Select “SC01” by pressing [UP] button. 2. Press [ENTER],
17 INSTRUCTIONS ON USE: The moving head is controlled by 15 DMX channels CHANNEL 1 : select one of the 9 colors, color cycle or rainbo
18 DMX channel’s function and values: Channel 1 – Color Wheel: 0-13 Open / white 14-27 Orange 28-41 Blue 42-55 Green 56-69 Yellow 70-83 Red 84-97 Ma
1Introduction Thank you for choosing Elektralite’s MY 250İ fixture. Please read the User Manual carefully and keep it in a safe place after reading i
19Channel 3 – Rotation gobo index , rotating gobo 0-127 Gobo indexing 128-187 Forward gobo rotation from fast to slow 188-191 No rotation 192-255 B
20Channel 8 –3 facet rotating prism, Prism / Gobo macros 0-3 open 4-63 Forwards rotation from fast to slow 64-67 No rotation 68-127 Backwards rotat
21Channel 13 – Lamp on/off, reset, internal 0-19 color change normal by direction depend on distance 20-39 color change to any position by directio
22 06Er: Tilt head movement error. This message will appear after resetting MY 250Ì and the head’s magnetic-indexing circuit malfunctions (sensor f
23Other Elektralite Products include : [Also check out our website at www.myelektralite.com] CP-3 Controller. CP-10xt Controller. CP-16 /24 Con
24CP-20xt Controller. TurboFog + Fog Machine.
2 Make sure that the power is only 120 volts. This unit will be damaged if you chose to install it at any other voltage. In an installation it is alw
3GENERAL GUIDELINES MY 250Ì is a lighting effect for professional use on stages, in clubs, theatres, and so on. This fixture should only be operat
4for a special wipe to clean the lamp. 4. Only install Philips MSD 250 or MSD 250/2 GY9.5 lamp. Any other lamp is not acceptable. Procedure: 1.
5. Safety-chainM10 X 25mm Using M10 (10mm) bolts screw the C clamps onto the base of MY 250Ì make sure that the bolts are firmly tightened but take
6 Method 2 : Installation using U Bracket Claps with half Cheeseboros/couplers. [The U brackets and the appropriate base for the mounting these brack
7 DMX has a maximum running distance of 330 feet. When long distances are involved then there is a tendency for electrical noise to be evident. In w
8 Projector DMX start address selection In order for the controller like Elektralite’s CP10xt to control each MY 250Ì it has to know where it is in t
Comments to this Manuals